ROUTER 設定+ 用icable broadband 的

2007-11-28 6:04 pm
我買左buffalo 個個router.
插左條cable 跟住 去執行到打cmd
係個dos 晝面就再打ipconfig/release + ENTER

個說明書就話會顯示到個ip address 係. 192. 168.11.1
但我個個就唔係..所有都係 0. 0.0.0
請問我應該點做同埋有咩辦法補救?

其實我之前已經上到ipconfig/all + ENTER
係見到個個ip address 192.168.11.1
但係我之後連上個個http://192.168.11.1 既網都上唔到.
請問我應該可以點做.
請問可否詳細少少咁講d procedure. eg. 要internet 設定 ( 由start --> 控制台 -->internet options--> connections --> LAN etc etc........)

十萭個謝謝.

回答 (3)

2007-11-29 9:56 am
✔ 最佳答案
Assuming you are connecting PC1 (desktop) and PC2 (laptop) to the router... the setup should look something like this:
Cable -----> Cable modem [Ethernet] -----> Router [WAN] -----> PC1 (port 1) PC2 (port2)
Insert the CD provided by Buffalo to the CD-ROM and run install, then follow the instructions for setup. If you have trouble for connecting the router, refer to the following website for more details
http://www.networkma gic.com/router-setup /setup.php
Once you have the cable connected as per the website shown above, follow the instructions to configure the router. Open IE and type http://192.168.11.1, you will then be prompted by username and password. Username is [root] and password is [leave it blank, do not type anything], then hit OK
Check internet settings and make sure DHCP or Dynamic IP is selected. Follow the wizard and setup the wireless settings if necessary. Save the settings and launch IE to check internet connection.
If you still have trouble connecting, reboot the modem and router. Follow the steps below:
1. then turn off the router first.
2. wait for 5 seconds, then turn off your modem.
3, wait for another 5 seconds and turn your modem back on
4, wait for all solid green lights on the modem, then turn on your router.
Close all IE and re-open IE to see if internet is now connected.
If you still have further questions, drop me a line and will provide futher help if needed

HTH

2007-11-29 1:39 am
你的說明書, 應該會有列資料的:
設定網頁的網址: 如http://195.168.11.1

正路, 只要你一插上隻Buffalo(留心不要插錯位), 佢就會派個IP比你, 便能連上去設定網頁~

假設你未曾改過隻Buffalo,及自己部機ge IP, 你只要關閉Buffalo及電腦的電源,
之後, 先開Buffalo,隔半分鐘, 再開電腦, 便ok架啦~
2007-11-28 10:48 pm
ipconfig /release 係用o黎 release IP o既!要重新取 IP,要打埋 ipconfig /renew!
renew 後,看看 Default Gateway o既 IP 係乜,然後o係Internet Explorer裡面輸入o個 IP,咁應該可以 config 到隻 router。當然要輸入login & password 啦!!!


收錄日期: 2021-04-14 00:06:05
原文連結 [永久失效]:
https://hk.answers.yahoo.com/question/index?qid=20071128000051KK00581

檢視 Wayback Machine 備份